USB RF Signal Generator – SynthUSBII The Windfreak SynthUSBII is a 34.4MHz to 4.4GHz software tunable RF signal generator controlled and powered by a PC running Windows XP, Vista, Windows 7 or 8 via its USB port. The SynthUSBII also has nonvolatile on board memory so it can be programmed to fire up by itself on any frequency, power, sweep or modulation setting. This makes for a highly mobile, low power and light weight solution for your RF signal generation needs. Please scroll down for more info on the powerful hardware and software features.

SynthUSBII Low Cost RF Signal Generator Use this device as a generic RF signal generator in your test setup, or use it as a high quality local oscillator in your RF / microwave communication system. Shown below, the software is eloquently engineered giving professional performance at fractions the cost of a bench top generator.

You may enter data either with the touch pad, knob, directly with the PC keyboard, and also by clicking on arrows next to the controls. RF single frequency generation tab. RF sweep generation tab. (Step as fast a 300uS per point. Resolution as low as 1KHz per step.) RF Pulse Amplitude Modulation tab. (Minimum pulse size and resolution is 1mS. Hp M7470n Driver Files Downloads.

Please see SynthNV for higher performance.) PLL Control tab. (Control some finer details of the ADF4351 chip to get higher accuracy or quality for a particular frequency.) Extras tab. (Check SynthUSBII firmware version, save to SynthUSBII internal EEPROM memory Frequency, Power, Modulation and Sweep setup for standalone operation. Also poll every second for phase lock.) RF power is controlled by two bits in the PLL chip. There is a total of 10dB of output power adjustment in 4 total steps.

Free Rf Receiver Driver Cm23e software download. Avangardo GPS generator PRO - Programming/Other. Packard Bell Usb Rf Receiver Driver. WLAN Driver Ralink RT257x (802.11a/b/g) USB Wireless LAN Card Version: 3. - Win Vista 64bit/Win Vista 32bit.

Please check out the SynthNV for more power and 1/2dB steps. The software is easy to install and use. It can control multiple devices based on programmed serial numbers, tune a RF CW frequency, run a RF sweep, Pulse Modulate, save many settings to EEPROM, and fine tune the PLL registers for experienced users.

Control is very similar to a bench top signal generator. It is also touch panel friendly. This software was written in Labview and the open source code is included so that you can modify and enhance any way you see fit for your own use. Please do not distribute. If you don’t own Labview, you will also get an executable that will install standalone and run on a PC. If you want to write your own software, it is best to get Labview and reverse engineer the Windfreak Labview source code.

Labview is available with a free 1 month trial from National Instruments. All source code is sent on CD “saved as” using the latest version of Labview Basic. The device is easy to talk to via 1 simple command character followed program data. For example, setting frequency is done by sending “f1000.0” (without the quotes). Click here to see the format for serial communications via the proprietary Windfreak firmware: Click here for the operating instructions included with the device: The Hardware. The SynthUSBII is made in the United States from parts purchased in the USA via manufacturers certified vendors. Cutehtml Serial Killers more.

The technology is based on Analog Devices ADF4351 chip seen here: You can expect high quality RF performance at the RF connector similar to the specs in the datasheet. RF power (max) into a 50 ohm load is similar to this: RF generator accuracy is based on an onboard 2.5ppm 10MHz crystal oscillator. All parts on the PCB are specified to operate from -40 to +85C. The synthesizer will run off USB power. It will also run standalone without a PC connected if you have a USB power supply similar to an iphone charger.

The required voltage is 5 volts DC.

ShareMe - free Rf Receiver Driver Cm23e download Categories • • • • • • • • • • • • • • • Top Downloads • BootRacer Tests How Fast is your PC! • The most powerful encryption software to. • Crave Accounting software is an easy to use.

• Money Manager Ex is a free, open-source. • AgileTrack is an agile/extreme programming (XP). • An intelligent freeware to fix common PC. New Downloads • Is your Mac becoming slow and unresponsive? • dbForge SQL Complete is an IntelliSense add-in. • SyncBreeze is a powerful, easy-to-use and fast. • Capture image from video.

FrameShots takes. • CRD is a Crystal Reports Scheduler that saves. • Photoshop Plugin for macOS 10.10 and later. • Real-time biometric face recognition and.

• Losing important data due to accidentally. • TeraByte Drive Image Backup and Restore Suite. • Dew Lab Studio is an object oriented. Recent Searches.